Hey, DIYers.
I'm George from Alarm Grid.
Today we're going to be going over what devices
are used with the XCVR2-345 Transceiver
on your Go Control 2GIG panel.
We know that as a GC2.
All right.
Our GC3 is the later version of the 2GIG panel.
As you see, it has a bigger touchscreen
on the buttons on the right-hand side,
and the GC2 has a smaller touchscreen,
two buttons underneath, and little speaker
holes on the top left corner.
Now the XCVR2-345 is what the GC2
uses to send out any commands.
Now typically the GC2 only comes with the 345 megahertz
receiver.
So that means it's only listening,
it's only able to receive signals, from the sensors.
So that means any bi-directional devices that you guys have--
keypads, Go!Bridges, image sensors which use 900 megahertz
frequency--
you would not be able to use on a GC2
if you have not installed the XCVR2-345 Transceiver.
Now we do actually have an install video,
the XCVR2-345 install to the GC2, on our YouTube channel.
So if you guys need help on installing it,
please look up that video.
Today I'm just going to go over some of the devices that use
this transceiver, starting with the first one,
which is going to be our Go!Bridge.
It's going to be our Go!Bridge IP Communicator for this GC2.
Now typically, just so you guys know,
the Go!Bridge is probably the only communicator that can be
activated through internet only on alarm.com.
Alarm.com normally requires every single one
of their panels to have a cellular communication
path enabled.
The Go!Bridge and the GC2 are the only panel that will allow
you to do internet only.
However, you will still be charged for cellular price
plans only.
So just because you have a Go!Bridge communicator
on your GC2 doesn't mean you will be able to sign up
for an internet plan with your alarm company since alarm.com
only has cellular-based plans, you will still be charged
for cellular.
So if you're being charged for cellular,
might as well just get the Go!Bridge and the cellular
communicator while you're at it.
Now GC2, it's still a common system that a lot of people
still have.
Some of you out there may need a firmware update
if you're going to be getting the new LTE communicators.
So there's a lot of things that come into play when
you're doing this, so it's always best
to contact your alarm professional,
and either us or they'll be able to help you figure out
what you need.
Now the Go!Bridge Communicator, it's an IP communicator,
internet communicator, that you plug directly into your router
with an internet cable.
From there, you actually learn it in wirelessly to your GC2.
And you need the XCVR2-345 so that this panel here can
communicate to the Go!Bridge Communicator that works with
alarm.com.
So not only it needs to be able to receive the signals from
that Go!Bridge Communicator, but it actually needs to be able
to send out the status.
So if you ever arm the system from the panel to Away
or if you ever disarm the system from the panel,
that signal needs to be sent to the communicator
so that then it can update alarm.com
if you guys have the service, and you guys can actually
make sure that the live status on your panel
is showing correctly on your app.
So it needs that XCVR2-345 in order to communicate back
and forth to the Go!Bridge communicator.
I'm going to show you guys real quick.
I'm going to open the panel up.
It's going to give me a cover tamper.
I'm going to show you guys exactly where it's
going to be installed just so you guys can see.
I'm just going to pull my panel directly off the back plate.
And if I look at the back here, if you
look at the top right corner--
I'm holding it upside down--
it's right across the battery pack.
It's this little silver piece with the black foam there.
That's normally where you would see your 345 receiver,
but that's what you're going to replace with the XCVR2-345
Transceiver.
All right.
Let me go in and put it back now.
Good.
All right.
So that is the first device that we're
going to talk about that needs the XCVR2-345 to communicate.
The second device is going to be the IMAGE1 Sensor.
The IMAGE1 Sensor transmits at a 900 megahertz frequency, which
for those of you who don't know, the XCVR2-345 not only works
at 345, but it also does 900 megahertz,
which is exactly what the Image Sensor communicates at.
So in order for this panel to work with an Image Sensor,
you need that transceiver module.
Now the reason why you also need that is because you don't want
the Image Sensor capturing images
while the system is in a disarmed state
and there's people at home.
You typically want the Image Sensor
whenever the system is in Armed Away or an Armed Stay mode,
maybe.
Typically it's going to be in Armed Away mode.
That's usually when motions are enabled,
and that's when nobody should be in the house,
and that's when you want the images to capture
anyone walking by that may set off the motion.
Now the third device is going to be the TS1 keypad.
The TS1 keypad is the touch screen keypad for the GC2.
That also transmits at 900 megahertz,
so you need that transceiver so that whenever
you arm from this keypad or whenever
you arm from the other keypad the commands are being sent
and they're actually syncing.
If you don't have that receiver and you're
arming Away on this keypad, that other TS1 keypad
is not going to know whether the system's Armed Away, Armed
Stay, Disarmed.
It's not going to know what sensors it has.
It's not going to have any communication at all
to this panel.
So that's why you need to make sure
that if you're going to be using that TS1 keypad for the GC2
that you guys actually have that XCVR2-345 Transceiver.
So those are the three main devices that
are used with this XCVR2-345.
Again, it's to allow your panel to work
with bidirectional communicators and devices.
Again, the things that we touched based on today was
the Go!Bridge IP Communicator, the IMAGE1 Sensor,
and the TS1 keypad.
If you guys have any other questions about devices,
feel free to go ahead and emails us at support@alarmgrid.com.
If you found the video helpful, make
sure you hit Like underneath, subscribe to the YouTube
channel, and enable the notifications so
when we upload new content you guys get notified.
I'm George, and I'll see you guys next time.