installing the lock wasn't too bad it took less than an hour but the programming part
was a little bit tricky that took a few tries so let me show you how I did it so there's a
million different types of electric door locks you could buy on Amazon they're all basically the same
um the model I bought was tiho and it is model number te001 it was about thirty five dollars
um they're all basically the same and they all get installed the same way so even if you don't have
this exact model the installation is basically the same and the only tools you really need is
a screwdriver but if you want it to go a little faster you can use a drill or an impact driver
and the first step is to remove the old deadbolt [Applause]
you got to get this cover plate off but to get that off there's a little Allen screw and of
course none of the Allen wrenches I have fits you might have to get a little creative deadbolts off
and once you remove the latch the cover plate there's just two screws that have to come out
foreign
I already have a faceplate on the inside of the door so I'm going to just leave that in
place next you can see on the lock it says up here in the top left corner so
this way goes up and this channel here is on the bottom this is how it actually locks
so that's how it's going to get installed in the door
and it says to make sure that this is centered in the opening if it needs to be adjusted you
take that you take the lock and you twist it and you can extend it out but mine's good
so that's how it's going to be installed the kit comes with short screws or long
screws to attach this plate to the door the original screws in my door were long so I'm
going to go with these longer screws and I'm just going to Loosely attach them for now
next is the face plate gets run the cord goes through the bottom
and this flat piece gets put through that bottom opening then on the inner part of the door
this manual lock this plate comes off and you can see it says this side against door
so it goes this way the wire gets run through the channel here on the bottom
and use the supplied bolts to attach the front and the back piece together
I'm just going to start them with the impact driver and then make sure it's
all lined up and finish it with the screwdriver
next you connect this cable to the connector here on the bottom
next you can see there's the little flat opening
here on the bottom and that aligns with the flat locking plate from the front
make sure that's lined up and then when you lift the battery compartment door there's
two screw holes and that's where you use these small black screws to secure this
plate to the metal plate this is where an extra set of hands helps or if you have a
little magnet on the end of your screwdriver you can kind of line it up screw it in place
next it takes four double a batteries
and you can test out the lock make sure everything moves freely
now that I'm happy with everything lined up I'm going to go ahead and tighten these two end screws
foreign
there we go so again you don't want to tighten these too tight because it becomes
really difficult for this lock mechanism to work and if I tighten up too much this
this lock didn't want to open that easily so just snug it up and get it nice and aligned
so now we're ready to set the lock on the door and first to test it to lock it you
hold any button down for two seconds so hold any button down and I can hear the motor it
engaged the lock so now it's locked so again to lock the door press any button for two seconds
Now the default master code is one two three four five six seven eight so to unlock it you
do one two three four five six seven eight press tihoe I can hear it unlock and the door unlocked
um now we're not gonna do any of these other steps add user delete user auto
lock we're just gonna do one master code for everybody so we're just gonna do this
top line here so according to this Top Line it says press T ho twice
press it again one long green beep that's right press one wait for the
flashing light now new master code let's try five five five five five five prestigo
and it flashed red it should have uh been a green flash it says when settings are unsuccessful
indicator light will flash red so apparently I did something wrong let's try it again
press T hoe twice one two three four five six seven eight prestigo again it should flash
long green press one two flashing greens that's correct I'm gonna do a coat of seven eight nine
zero press T how it flashes I'm gonna do seven eight nine zero it flashes that's successful
that's the new lock it didn't work the first time I tried it because I was trying to do one through
eight again or zero zero zero zero zero at least for me what worked is just a four digit code so
um you can see now that the new code is to lock it you just hold it
two seconds the door is locked to unlock it 7890 tihoe and the door is unlocked [Music]
one last thing is it also comes with keys in case you forget your lock you can unlock it that way
so I hope this helps again doing the lock itself wasn't that complicated it's figuring out which
screws go where but programming was a little bit tricky getting this code to work and it didn't
work the first couple times but uh it should be pretty easy and straightforward and you
only have to get it right once and then you never have to do it again so I hope this helps thanks