Hey guys, It's Rolando from ReveMoto. Today, we're going to be doing a 2010 Chrysler 200
front bumper replacement. All right so when you're putting the bumper back in, make sure
you're aware of the lower cover that it goes in inside and doesn't flap down the bottom so
you're gonna have problems with insulation if you do do that. So first I like to be
lining up in the middle.
All right before I do anything else, I'm just going to secure the top while I work on the sides.
All right since the bumper is lined up, finally we're going to secure it
real quickly with this screw.
So now we know the bumper is not going to fall off, we're going to go to one side.
So this one the rebar is messy with alignment but basically you got to get it over this
and then the bumper right here.
You have to get it over the... the bracket also.
So make sure it's over the bracket and then you can push this in.
All right guys so we finally got it to pop into place but basically the rebar
was costing us a little bit of an issue because it's pushed in so it's pushing the uh the bumper
back. So once you guys get the uh the bumper intact on one side
put a screw on it just like I did. If you guys come over here.
I put that screw back on there. I'll tighten it up.
So basically it's gonna hold this part while I work on the other side.
So on this side, I went ahead and... popped into place. We have a small little gap right
here that's because of the rebar is pushing this bumper that way but the customer didn't
want to fix the rebar. They want to fix it later and that's perfectly fine but we do
highly recommend that the rebars are changed out because that is a reinforcement bar that's
that uh causes the impact of an accident to be a little bit less so it's a safety issue basically.
So once you get... get this bumper lined up, let's go ahead and get the screw.
Let's screw this one into place.
Okay so I'm gonna go ahead and get the other screws put back on here. So on the...
we had difficulty removing these screws on that one side.
So basically what you do is you go into the back of it you come on this side.
What was happening was this thing kept on rotating like that.
So basically what you do is just hold down on it.
It comes right off. So if you have difficulty taking it off just go
ahead and take out the whole bumper and it's easier for you guys to hold it like this.
All right, I'm gonna put this back on the other side.
So basically this this plastic piece
goes into this hole right here.
Just like that and this hole right here like that push it back into place
and you can go ahead and screw it back in.
Okay, so we'll work on our way on the bottom.
So we're gonna put this push pin back in so basically it's on this side.
Push it and then push it down okay.
So it wouldn't be so hard if the rebar wasn't pushing this out but
I'm gonna work with it i'm gonna put this one down.
I'm gonna put this one in first right here.
So I'm gonna go ahead and put this in.
So the other two screws won't pop into place because it's just...
it just won't line up correctly but we'll put the side panels back on
and this one's missing the retaining pin so we'll get another one on that one.
So we're going to go ahead and go to the top.
So we're going to take off the screw that we used to hold the bumper into place.
I'm gonna go ahead and put that glue back on.
So make sure you put it underneath the...
I think it's like an intake first. I'm gonna put the screws in
and I'm gonna tighten it down
and then we're going to go ahead and finally put the twist pins in place.
Okay so once all the chips are back on that's pretty much uh a done deal so basically all
you need to do is put the screws back on there with the... with the license plate.
All right so it's a little bit faded on the uh bumper but basically if you bring out the shine,
just a car wash and also buff it out west end and buff it out
the shine would be just like the brand new bumper.
All right guys so that's how you install 2013
Chrysler 200 Front Bumper. If you guys like this video go and subscribe to us
turn on the push notification for other videos that we do have and if you guys need any parts
for your vehicle go to ReveMoto.com where we sell pre-painted auto body parts. Thank you.