I'm gonna show you guys how to install printheads on a workhorse tough
automatic screen printing press show you how we did it coming up you'll have to
excuse the audio on these first clips I was using my iPhone and for whatever
reason the iPhone just doesn't capture audio as well as the camera but I think
he'll get the point let's dive into it
before I install this head I bought some new airline and I'm going to use this
tape and marker because there is a red and black line that does
to these houses here
we have our stroke cylinder which is the green and blue and then the red and
black at the flip cylinder and then the smaller black one is the clamps for this
screen with screen clamps and if I pull these wires out of here or the pneumatic
tubes you can see here are the tubing's I did
we replace it with some new pneumatic tubing but because this is all black I'm
going to label one of these blacks that way I know it will go to the black one
and other tubing will go to the rest connection so all I'm gonna do is take
this tubing and I'm going to feed it through this hole here this is where it
actually comes out and I'm just going to keep feeding it in hotel with
come out the backside
and make sure I have plenty of room here to my strength under
and I'll flip this thing over to show you exactly how this look good so I have
this label next thing I'm going to do is run the red cable through which will
come from here go out through the front just like this one and I'm then tubing
that cable down through the body and out through the back now that I have the red
quote-unquote the red hose ran and the black I have some slack up here at the
front that way be nice throw period
move back and forth I'm just going to trim this down so it's not as long
now what I'm going to do is lift this head up I'm leaving
the front part off just for the moment make it a little easier on me I am doing
it solo the stroke cylinder here will actually go inside this hole right here
and then arms sit on top of here and then place it on here I'm going to use
this ladder to aid me and holding it and then we're going to connect everything
up tuck these cables way inside the arm or either the body here and then as you
can see here there are four bolts
sticking up and which the head bolts to
you see on this head is already connected these are the little caps that
go on okay so I got this thing almost there
you can see how the stroke cylinder goes into the bottom hole here we are sitting
on top of these two bolts here I do have it offset just a touch that way those
bolts do not fall into these first holes and I can slide it back and then I'm
going to tuck these pneumatic cables away bring it all the way to the front
and then I'm going to install my four bolts and tighten them down to 65
foot-pounds I have my cables all curled up and tucked in here now I'm just going
to slide this thing forward seat it down in position and then put at least one
nut on in the back and then I can take it off of this ghetto rig that I am
using as far as doing it one-man style one thing to note when you are sliding
this arm on you do have to move the arm up and down just to get past the the
front and the rear bolts not gonna hurt your stroke cylinder any and submit the
Flex a little bit so I got a little hung up had to lower the front this arm down
push it forward and now it's seated in place and I'm gonna toss the bolts on
thanks ladder helper okay guys so here we are I have every single head
on the press I've got both of the flashbacks hyung get a little cramped in
here I'm ready to fire this thing up here in their future that way I can
break down this manual because you can see it is really tight in here right now
as soon as I break that down everything will be cool but I need to test this
thing out first thanks for tuning in guys I really appreciate it if you're
new to the channel be sure to subscribe if you're in the market for screen print
supplies or equipment these are promo code Mikey designs at
Katz's Pitt screenprint supply.com you'll get five dollars off your screen
printing supplies or equipment purchase and it will help support our channels
that way we can continue to make videos such as these for you until next time
guys we'll see you later
you