hello young as estánsoy Reyner today we will work on our platform study
but we talked together and we will next exercise and good is quite interesting
hope the videos they are serving and are sharing in their social networks then
says in every tenth the following We are going to solve this situation right now, he says, he elaborates
the diagram of more than force of two double effects cylinders which describe the following
electropneumatic sequence fulfilling the following working conditions, well the sequence is more
than more then there you see - that means that it will come out first and then it will go out, go and then both
return to their initial position then here is a simultaneous movement if you want to learn more
about this you can go to see the flushing tutorial videos where we talk about modem and simultaneous
movement then the first working condition is When you press start, the
cylinder rod of the cylinder effect comes out three seconds after the double
effect cylinder rod sees comes out what we have here goes after 5 seconds both return to their initial position which
means that here we are going to measure the times the time that comes out when it comes out and that it waits for it to
come out go after five seconds with both of us outside so that they return to their initial position
and this cycle is going to be repeating three times to be automatically paid, it means
that here we will need a meter and the necessary signals we know how what
is command what is true what is control for emergency the stop the machine and the ignition
with its counter, all that is true, we already handled it and also the signals, both a signal
that the cylinder is carried out outside another that the cylinder outside is analyzed and we are going to put
a red light that is carried out when the system is stopped that's all then we will go to the
software here we say to make the assembly and the interconnections of the tire elements ee
yy
care
no no
hello
and
never
and young and here we already have most of the components and
our software there is only a small detail that I did not anticipate from the beginning and it turns out that I
had changed some are some buttons so I am going to explain which is the wrong one
sorry, some sensors, I'm going to apply which is the sensor that is bad so that you can
repair them and in that way it works everything correctly so we are going to put our
control box so to speak here we have our control box then what I
had for you to check that this magnetic limit switch is in this position I
had it changed with this limit switch then the limit switch is exchanged position
with this magnetic sensor just make sure that the correct names go that is what we have
here then that we already have our diagram interconnected the two double
effect cylinders the first effect cylinder we are going to work with a limit switch and the second
is monitored the movement by two magnetic sensors we already have its two timers the timer
1 the timer 2 they are read today from the magnetic limit switches the mechanical
limit switch the counter that we have already reset its contact that activates it now We have entered all three of them, he was able to
configure their pulses and nothing now we are going to do the simulation so we are going to simulate it
starts on activated the sensor sees 0 because it is the only one that is currently activated
then when pressing start what happens is that it goes out and is see him later after three seconds
do not set the time I think it was three seconds the cylinder comes out of both lamps both
are marked with a green lamp so let's see there the cylinder comes out when it
reaches its end of stroke it begins its journey the cylinder sees the foundations are working
then the green lamp is there both must be outside for a while then they return at the same
time to their initial position and so what and it repeats itself then we are going to configure LEDs a
little more time outside and in addition to that we are going to put it a little faster so
that we can see how it works this we are going to take it here since it made us a little bit of a situation
there we are going to put the fastest so that they can see how fast they work now we are both going to
increase the speed to 100 percent and now what we are going to do is good the first timer
has three seconds we are going to give it like this the second timer has four seconds to put six seconds
out 6 seconds out where they are 6 seconds out so that it works in this way
well let's see how it works now let's see how a worker press start how we can see
the times are now faster in the route of the shoots are faster there has
to be that time outside and both return to their initial position when the time ends they enter and
leave again and in that way now it is seen a little faster the process and well there is nothing
more to say I believe that this here there is nothing more than to put it true if there is some detail to
fix because perhaps it is the times or in some contact out there that is not true I do not know right now
I think That we are going to leave it there more but if there is any detail then again remember that
a perfect situation can be seen there and I thank all those who are
watching the good content, the three cycles are already over, and it has stopped I must give it
back so that the counter is respected when the counter is reset it returns to zero
it returns to its normal state as we can see there it starts the process again I thank
all the people who are sharing the content on their social networks and those
who leave their comments also later I will be doing some greetings to
all the subscribers of the platform of let's learn together with professor rainer,
have a good day there, please, I thank you for your kind attention n and if you have not
paid attention we do not believe for something you are watching the video have a good day anyway
yi