welcome to the super pump vs variable speed training video
this video will cover installation programming and troubleshooting
it is provided for you to better understand our products
and how they operate before beginning installation
make sure to read the installation manual included with the pump carefully
and completely this video was designed to serve as a quick overview
and does not replace or supersede the detailed installation
operation requirements set forth in the products owner
and installation manual for a free additional copy of the manual
please visit Hayward.com as with all Hayward pumps
make sure the pump will not be located in an area
that may be subject to flooding submerge pumps or motors
are not covered under warranty
to ensure proper operation make sure to supply the proper plumbing pipe size
and configuration that will maximize a superpump
variable speeds hydraulic efficiency take care when plumbing the pump to avoid
allowing PVC glue
or primer from entering the internal pump or drive components
in addition make sure all electrical wiring conforms to local codes
regulations and the National Electric Code the superpower variable speed operates
at 230 volts AC
60-hertz single-phase voltage the amp reach is rated at 5.9
the pump is not designed for 115 volts
AC installation wiring 215 volts will cause permanent damage to the motor
and drive
also ensure the pump is properly bonded and grounded for safety
to begin installation turn off all electrical power at the circuit breaker
next remove the wiring access cover on the motor drive
this is done by removing the four screws on top of the cover
using a three millimeter hex wrench
when the cover of the drive is removed care should be taken to ensure no wiring
strands
or other debris are allowed to fall into the drive area
or motor next remove the three wires that service test leads
for factory performance testing they are connected to terminals
l1 l2 and ground these leads are not to be used to connect load power to the
pump
next connect the 230 volt AC line power supply wiring to the terminal block
and ground wire to the ground screws as shown in the input power wiring diagram
in the manual you will notice the ground lug incorporates a washer
so make sure it does not fall into the internal section of the motor
or onto the circuit board of the drive make sure to utilize a water tight
conduit connection
to the pumps drive to ensure no water gets into the pumps drive
or motor
connect the pump to the pool bonding system using number eight
bare wire for Canada number six pair wire is used
a lug for bonding is provided on the outside of the drive enclosure
after all electrical connections have been made replace the wiring access
cover on the motor drive
make sure the motor lead wires are routed in such a way
that the wiring access cover can be installed and seeded fully
without interference note that the screws are two different links
and that the longer set of screws should go in the rear holes of the drive
in addition the display cannot be rotated 180 degrees
it must stay in its original position facing the rear of motor
now we will review start up and programming
first we see the pump display as viewed when the pump is not powered up
you will notice the power LED at the top left as well as the display
are not illuminated in addition the LED's for the speed buttons
v1, 2, and 3 are not illuminated
when power is applied to the pump we see that the power LED is now eliminated
and that the display shows the drive revision number and then the RPM's
of the pump while in prime
mode while in prime mode pressing the display function button
well advanced the display to also show the amount of time remaining:
and prime mode as well as the amount of power being consumed in watt's
the pump is set to start in the default prime mode
which is three thousand RPM's for three minutes
when priming is complete the pump will switch to speed v3
the pump will then run at v3 speed for its program time
and then switch to speed v1 the default speeds and times are as follows:
v1 1500 rpm and no timer
v2 2400 RPM's for 12 hours
v3 3000 rpms for 12 hours
to configure the pumps speeds and timers
begin by pressing and holding the display function button
until the configuration menu is displayed
the first selection will be the prime mode. press the up or down arrows to
adjust the prime time
from 0 minutes up to four minutes Next press the display function button to
edit the speed setting for v1 you will notice the V1 LED is now
blinking to indicate the pump is in the configuration menu
the up and down arrows are used to adjust the speed between six hundred RPM's
and 3,000 rpm which are the minimum and maximum speeds
for v1, v2, and v3 pressing the display function button again will
display the speed setting for v2
use the Up and Down arrows to adjust when the display function button is
pressed again
you will see the timer setting for v2 to change
press the up and down arrow buttons to adjust the time
anywhere from thirty minutes up to 23 hours and 30 minutes
next press the display function button to change the speed setting
for v3 press the display function button again
to change the timer setting for v3 when changes are complete
Press that display function button to save settings
now we can view our changes by pressing v1
v2 or v3 when we press v1 we first see the speed
that is currently set pressing the display function button
well display the current power consumption shown by the letter P
when we have selected either v2 or v3
pressing the display function button once will display the remaining time
left on that timer
shown by the letter H press in the display function button again
will show the current power consumption for that speed
when the run stop button is pressed it anytime during normal operation
stop will be displayed on the screen the pump will come to a stop
and will remain stopped until the run stop button is pressed again
at which point the pump will resume normal operation
to make a quick speed change to either v1
v2 or v3 while they are running press the up/down arrow buttons to increase
or decrease the speed the LED for the change speed will begin to flash
to save the speech change press both the up and down arrow buttons
at the same time the LED should now be solid
showing that speed has been changed after prime mode the pump will
automatically go to speed
and time for v3 it will then change to v1
after the time set for v3 is complete v2 can only be engaged by pressing
the V2 button
the pump does not automatically switch to v2 at any time
here is an example of a possible installation for the super pump vs
we can connect the pump to a switch time clock
or filter control relay of a controller for daily startup at v3 for
speed
and duration and then the pump will automatically change
to the speed v1 at the end of the v3 cycle
as an example we could start up in v3
as a cleaner speed and then run v1 at a lower filtration speed
this leaves v2 available for non-daily applications
such as backwash we are now going to talk about basic troubleshooting
when troubleshooting the pump it may be useful to run the pump
without program functions being active this can be done in the service mode
which only allows for motor RPM's to be changed
service mode is entered by removing power to the pump
and then pressing and holding the display function button
as power is turned back on test will then briefly be shown
on the display and the LED's for v1 through v3
will blink together to remind the user service mode
is enabled the pump RPM's can now be adjusted using the up and down arrow
buttons
to exit from service mode cycle the power to the pump
off and back on if needed you can reset the pump to factory default settings
remove power from the pump and then press and hold the run stop button
while applying power back to the pump when the pump is turned back on
the screen will display reset confirming that all settings have been reset to
factory default settings
the pump will then begin to operate in prime mode
for professional help and service go to Hayward.com
and select dealer locator which you will see at the top left of the website
navigation bar next provide the zip code of where the pump is installed
as well as one a search radius
two Pool type 3
product repair & service and four
variable speed pump lastly
select submit and you will see all local Hayward authorized service centers
who can assist with Max Flo vs installation
programming or service thank you
for taking the time to view this video we hope the information contained here
has helped you with your Hayward super pump variable speed pump
remember to visit hayward pool products
at www.hayward.com
along with our social media sites for helpful information about your Hayward products