Hey [? DIYers ?] Jarrett here from AlarmGrid.
Today we're really just going to be going over
how you would set up the partitions on your Qolsys IQ
panels 2 plus to trigger the alarm siren.
If you go ahead and set up the partitions on your Qolsys IQ
panel 2 plus without enabling a certain option
within the panel not all of the partitions
are going to sound the siren.
We're going to be going with that option in a little bit.
But just to go over and at least give you
a little bit of information about partitions just in case
you're not really familiar with them.
Partitioning is essentially like sectioning off different zones
that you have set up on your Qolsys system.
So say in a home where you have an office where
you have some sensors and office and then you
have some sensors in the living room.
So if you want to go ahead and arm the sensors in the office
but leave all the sensors unarmed in the living room
then you would set up different partitions.
So for instance you would setup the office on partition two
and you would set up the living room on partition one.
So if you go ahead and arm partition two,
then all of the sensors that are on partition two
are going to be armed and if any of them
are triggered or having them [INAUDIBLE] it
will trigger the siren on the Qolsys panel.
But all the sensors within partition one
which is in the living room are not
going to trigger the siren on the Qolsys
because those are all disarmed because they're
on the separate partition.
So if you have different partitions
you can arm and disarm certain areas of the home
without one affecting the other.
So one last thing I'd like to add on
about setting up the global intrusion
sound and the sirens option on the panel, the only way
to be able to get to those options
is if you do set up the partitions on the panel.
If you don't have the partitions enabled then
you're not going to be able to see or enable
those different settings to have all the partitions sound.
So I want to enable those partitions
then you'll be able to edit those different settings
and set everything up the way you would like to.
Now once you do set up the partitions on the panel,
the panel is going to ask you to enter and the installer
code to be able to confirm those changes.
Now, any time or once you have those partitions set up,
any time you go to wake up the panel
or you going to access it, it is going
to prompt you to enter the installer code again.
And then once you do, it's going to give you
a little good morning installer menu or a little window
and then you'll be able to access all the panel,
again you'll be able to control everything you need to.
Now, once you do that whenever you go into the advanced
settings option, it's not going to ask you for the installer
code at that point anymore like it would normally when you
don't have the partition setup.
So you want to keep that in mind whenever
you go into the settings and everything.
Don't want to get you confused whenever
you're going through that.
That is just a thing that happens with the Qolsys
when you go ahead and enable the partitions.
So if you wanted to go ahead and set up your Qolsys to have all
the sensor sound on the partitions
or if you have all your partition sound
whenever sensors are activated you're
going to follow these simple steps.
So on the panel itself you're going
to go into the main menu and everything
and then you're going to go into the settings option.
But what I wanted to show you real quick
is what I meant by that a little prompt
coming up to enter the installer code to be
able to access the system.
So right now, the system is locked.
If you tap on it, it's going to bring this keypad up.
So this is where you want to type in the installer code.
Which the default is 1 1 1 1 and then
it gives you a good morning installer.
So now you're into the system.
So once you're done with that you're just going to go
and you're going to tap the small gray bar at the top
and you're going to tap settings.
Then you're going to go into advanced settings.
And notice how the mask for the installer code.
That's also what I meant but normally
if you were to go into the advanced settings
and you don't have partitions enabled.
It is going to prompt you to enter the installer code
and again, the default is 1 1 1 1.
But now that we're in this menu all you have to do
is go into sound, and then you're
going to scroll down until you see
the option for global intrusion sound and sirens.
So as of right here we have partition sounds.
So we have global fire siren, we have global intrusion sounds
and sirens, we have global auxiliary sirens,
chimes and voices, and all sounds on partition one.
So if you wanted all your partitions
to sound if any sensors were activated then
you're going to tap, you're just going to hit the checkbox.
If you want any auxiliary alarms to sound on all partitions,
you're going to hit the checkbox as well.
Or yeah.
Now, for the auxiliary sounds--
basically that is if you were to go into the panel
or if you had a key fob and you were
to trigger a panic option whether it
be like a normal panic on the system or a key fob,
medical panic, or even a fire panic
and whichever partition you're using at that time, whichever
partition you're at you can and you go ahead
and trigger those panics.
It's going to trigger the alarm on the panel.
If you don't have that enabled then
it is not going to trigger the alarm on the panel.
So if you want to make sure that's the case
you're going to go ahead and enable this option.
Then you have global chimes and voices for all the partitions.
Basically if you wanted any of the sensors
to produce a chime or a sound on the panel whenever
they're faulted you're just going
to enable that option as well.
So you're just going to enable that option.
And then all sounds and Partition one basically,
if you have any sensor set up on partition one
and you wanted to have those sound
then you can enable that option as well.
But for right now, this is the main focus
which is global intrusion sounds and sirens.
Once you have that enabled, all you have to do
is hit the house button and I'll take you back
to the main screen.
And all of your changes will be saved automatically.
And that is how you set up the sensors on all your partition
to sound on the Qolsys IQ panel 2 plus.
If you have any further questions about the Qolsys IQ
panel 2 plus or alarm systems in general,
please contact us at support@alarmgrid.com
or go to our website, alarmgrid.com.
If you found this video helpful please like and subscribe.
For your notification to future videos
please click the bell icon.
This is Jarrett from AlarmGrid.
You have yourself a great day.