friends A huge hello to everyone Today we will try to make a homemade product from such
a spring, what will happen Let's watch a video for you all Have a nice viewing friends went,
in general, I re-replaced the spring ,
re-navigated it or how it will be right
we’ll use it like this
now let’s go weld it
like this I scalded
it like this I sharpened it on a cone now we’ll harden it
[music]
it turned out like this now I’ll degrease all this
beauty my friends bought this handle this Birch now we’ll cut off a piece of
the lower part I made 750
30 millimeters
[music]
and I put on our first cut off part clearly
now the handle remains to be processed I will process with an ordinary stain Mahogany
dry wood is absorbed very well
friends the handle is dry Here everything is also dry now we dress it right very well here comes
the design is ready Let's go try Why
done , we also try it with thorns
with long
roots ;
that here, after all, friends, as a result,
we got a fully working tool, I didn’t even expect it, I thought it’s worth it So garbage, because it’s
worth it It’s sold on the Internet for almost 1000 rubles, it turns out that the topic Work is done
straight easily and quickly at least cost minimum effort we will make a homemade product of such an old
the springs, it’s already broken, the first thing I took was a brush and I’ll clean up the dirt now,
of course, this spring of some kind of car I don’t know this, I found scrap metal, of course,
to embody life, you can buy it in a store, but why buy If you can do it yourself,
I cleaned the part that I need to take 4 regular Cable is one and a half squares, but
you can use a rope. I just mark what is at hand somewhere around 27
millimeters, now I bite off the wire and press it tightly against our future workpiece,
make a mark on the cut line, so we make 4 pieces friends by the way Nobody knows C what
alloy this spring is made of If someone knows, be sure to write in the comments
now we cut it to the right for a mistake, I don’t have
4 pieces cut off a couple of millimeters, it’s all brought up then you see it
has a little bit of a kind of bend, that is, it’s also right for
us sharpened approximately
clamped the profile pipe 40 by 40 and cut off a piece somewhere about
40 millimeters in a square found the center of the four sides make through holes
to the size we need here the diameter of our spring turned out to be such a square now we take our rods
and now we will set them at a certain angle and we’ll scald, yes, that is, Well, it’s clear
that it’s like a factory Tornado, we’ll now set the corner, I’ll go grab it and then I’ll show it
took the 25 pipe a little bit I cut it out now, we’ll grab the shot now the handle is now also
friends Well, as you can see, I painted everything except for the pins themselves
Well, what to protect from welding didn’t, I think Let’s try How we take it
Yes, virgin
soil is soft earth, then there’s nothing to say at all, that is, even no effort loosened if
you need something that was dug Yes, I dug up nothing planted friends Well,
as you can see, it turned out to be a completely working tool The only thing so that I add a
plastic plug here so that the Earth does not get stuffed so I would change it initially, of course it would work, but
not initially slightly changed the distance between them a little less, that is, I would
make the angle a little smaller and tilt it a little To make the bowl itself smaller in principle it works I think
these pins will last for a long time after use, be sure to rinse and dry And that’s it And nothing
will rust the pipe is protected it’s useless to paint I think it’s homemade with the remnants of
a polypropylene pipe, namely this Thirty-second and 20 20 pipe, we also have a corner of
the second pipe
3 cm we make a markup one and a half then markup 2 again one
and a half two and a half and then there are two of us left
Well, what happened
I get This is the picture now we need to transfer it here, of course, it could
have been a little on the pipe But damn it on paper it was much more convenient to do it now it remains to
cut everything out of the pipe, it turned out like this, but I decided to drill two more
holes and cut the piece in half, then I heat it All this with with the help of a gas burner
and I insert the pipe into it so that it sits more tightly and doesn’t go anywhere, maybe there were even extra
holes, but nevertheless I’ll leave it to cool down friends So that’s how it turned out
here I made it look twisted it all cooled down Now we’ll solder there
is also a piece of 30 centimeters 32 pipes we will immediately divide it in half from
the top, I make a hole in the center,
now we take the twentieth pipe, we cut off from it, the meter
took the plugs 20 into one, cut off the half, too, now we will solder
the twentieth pipe, we put 32 from the back side
and also solder the plug all the tool we have ready
friends we have with you it turned out such a tool, nothing bends all the windows, the only thing is
that I would add a spring here to return yes Well, in principle, it
is not needed when we stick in, push the ground, then it pulls up according to its gravity, goes in the opposite
direction, you also knock it out here Of course it was spring It was just always in this position, it was such a
constant cross, the idea we got right, even very Working 20 millimeters wide
and a piece of 60 millimeters, now we will mark somewhere, leave the middle of 10 millimeters,
such a fork turned out to be eaten on such a round timber of a dozen 160 millimeters, now I’ll cut
it all off we take the case and insert it into the slot, so I even set it a little,
it just turned out at an angle, we also need it now behind the scenes I’ll scald it all,
so such a fork turns out I found such a piece of the plate now
11 millimeters we note, but I already figured it out I found the center
did by centimeter and also found the center here, let's make a rhombus so peculiar
[music]
like this, we'll grab it in this way, I said it now, I quickly all came in.
This is the kind of thing that turns out guys who already know what it is Write in the comments who already
guessed Who uses Of course this probably already knows the thing
and guesses now quickly paint it to make it beautiful
I took a bar I want to make a handle Of course you can make it simple there
take some piece of round board and drill a hole to put Well I do it
for myself I want to do everything beautifully now processing can be done with a piece of wood we make a handle
[music]
In general, everything has dried up Everything is ready This is how the device turned out Who knows what it is for who doesn’t know
I’ll say it for Dubai now I’ll go and show you everything I just mowed the lawn yesterday
Here But I’m pissed right off these dandelions and actually we get armed with this
thing, we look at the base, we stick it in and pull out the root, and so
you see Yes, that is, the lawn
will not be clogged now And they won’t get out until it comes out a new one, then we’ll do it again
like this, such a bunch turned out to be carried away, I have piles lying around everywhere
The only minus Of course Here such holes are obtained from large tables, but nevertheless,
in general, friends, this is how we got a working tool, it’s a really cool
thing, thank you to all of you who watched this video, who haven’t subscribed yet Subscribe,
but I will continue to tear the roots