Hey, DIY-ers.
I'm Jorge from AlarmGrid.
Today, we're going to be going over whether or not
a 5800COMBO works with a Lyric alarm system.
So the 5800COMBO is a wireless combo smoke-CO-heat detector.
So this sensor actually takes up to five zones
if you program it to do all the functionalities.
I'm going to go over some of the functions in a second here.
So first of all, this uses a photo electric smoke detector,
has a little gas chamber right here.
It also has a fixed heat detector.
So once the temperature hits 135 degrees Fahrenheit,
the heat detector goes off.
It also has a freeze warning.
So once the temperature has dropped
to 41 degrees Fahrenheit, the freeze detection will go off.
And then it also has carbon monoxide detection as well.
So not only are you going to be able to program
it to do smoke-CO, smoke, CO, heat and freeze,
but you also can have the system programmed to notify you
whenever it's end of life or whenever
you need smoke maintenance.
So the five zones that it can actually do
are smoke and heat, we got CO, we have freeze warning,
and then we have a smoke maintenance,
and an end-of-life notification that
will let you know when these need
be replaced which is usually about every eight to 10 years.
Now, I'm going to show you guys in a second
that this detector does work with the Lyric system.
Now, this transmits at a 345 megahertz frequency.
And the Lyric system has a 345 megahertz receiver.
Since both of these devices are Honeywell, which also is now
known as Resideo They broke their alarm division
into Resideo so we now call these Resideo
devices, Resideo Lyric alarm system, Resideo 5800COMBO.
Since this is all working on the same RF frequency,
they will interact.
And I'll show you guys right now.
If I actually go into my Tools, so I'm going to hit Tools,
I'm going to enter my installer code, 4112.
Yours may or may not be different.
I'm going to go over to programming, and I go to Zones.
Now, I'm not going to show you guys
how to program this sensor.
We actually have a video that shows you
how to program the 5800COMBO into the Lyric,
but I do want to show you guys that I have every single sensor
zone programmed into the Lyric system.
So if you see here, I actually went ahead
and I made 3, 4, 5, 6 and 7 all programmed with this sensor.
So you'll see here on number 3, I have my living room smoke
detector.
It is also the heat detector.
That is, smoke and heat go on the same zone.
We have a living room carbon monoxide.
We have the temperature sensor.
And then we have the maintenance for the smoke.
And an end-of-life for the CO.
Now, one important thing, when you guys are programming
this sensor in is you do have to realize there are
two separate serial numbers.
One is the serial number for the smoke sensor and the freeze
detection.
That's going to be the normal serial number.
And then the CO is the serial number
but the last number is one higher.
So the CO serial number is always
going to be one digit higher than the smoke serial number.
And if you guys want to confirm that,
you can also go in to the Actual Zone and hit Edit.
You'll see my serial number loop one.
Now, to get hold of the different features
that the sensor actually does, you
need to use the different loop numbers.
So for instance, my smoke and heat, and my temperature use
the same serial number but my living room temperature
is on loop three.
My smoke maintenance is on loop two,
so that's same serial number through all three.
My carbon monoxide zone is one digit higher
and it's set to loop one.
And then my end-of-life for the carbon monoxide
is same serial number set to loop two.
Now to prove, I'm going to go ahead and back
out all the way to the main screen,
and I'm just going to set off a quick alarm.
I'm going to just test the smoke and CO to show you guys
that it actually does work.
So I'm just going to press and release for one second.
Press, release.
Smoke sensor is good.
Battery life is at least 12 months.
The alarm will now sound in five seconds.
Press test to cancel.
Gives you a little bit of status from the sensor
and then it'll go off in a second.
As you see, we're getting the fire on the panel.
I'm going to go ahead and disarm it.
And you have to disarm twice when an alarm goes off.
So I hit disarm again.
So that was my fire.
Now, my CO.
Again, just press and release.
CO sensor is good.
Remaining sensor life is at least 12 months.
Battery life is at least 12 months.
The alarm will now sound in five seconds.
Press test to cancel.
I'm not going to cancel.
I want the signal to go through.
Carbon monoxide on the panel.
Just go ahead and disarm.
All right, so I'm using my master code
to disarm the system.
Now, you can also test the freeze detection if you want.
You can grab a bag of ice and put it on the sensor.
Once they hit 41 degrees Fahrenheit,
the freeze detection will also go off.
One of the ones that I didn't go over,
which actually doesn't need to be programmed because it's
an automatic, I guess it's an automatic trouble
if the tamper goes off.
So if somebody is messing with your smoke and heat
and they take it off the back plate as I'm about to do now,
you will get a tamper on the panel,
and it's not one that you have to actually program.
As you see here, it says tamper.
And since this is technically my smoke seal and freeze,
I'm going to get a tamper on multiple zones
as you can see here.
So he showed up three, four, five, and then six and seven.
So to fix the tamper, you'd have to put the back plate back on.
Simply twist, and the tamper will remain on the screen.
So you have to disarm it.
That way, if anybody ever messes with the sensor,
and then tries to put it back together,
and expects you to never know about it,
well, the system will always let you know
and you have to acknowledge it by entering in your code.
I'm going to disarm again.
Now, one thing with these sensors is that these do not
have the one-go-all-go feature that the SIXCOMBO does have.
So if you guys have a Lyric alarm system
and you're looking at getting a combo detector,
we have this in SIX series encrypted.
Which means it's 128 bit AES--
Advanced Encryption Standards.
And it actually has a one-go-all-go feature.
What that means is if one smoke detector goes off,
all of the smoke detectors in the house
as long as there's a SIXCOMBOS and they're interconnected,
which means you have that feature enabled
in the programming, they will all go off.
This 5800COMBO combo does not have it.
It just doesn't have that feature.
So if you guys have any questions at all,
whether or not this 5800COMBO works with your Lyric system,
if you guys have any questions whatsoever
on how to get it programmed or even monitoring,
feel free to send us an email to support@alarmgrid.com.
If you've found the video hopeful,
make sure you hit Like on the underneath,
subscribe to the YouTube channel,
and enable notifications so when we upload new content,
you guys get notified.
I'm Jorge, and I'll see you guys next time.