(music playing)
Glad to say after, dam a couple of weeks of waiting I finally got the pulley that was on back order
I've got both belts
hopefully we can get this thing together and done today
and out the door
and ah
bless it and whatever (laughing) let's go
we're going to put the two lock bolts back into the pulley
and this should go right on there
nice
so to change your oil
use just an adjustable wrench to take this nut off here
from what looks like a pipe, you loosen it
using a funnel
you can direct the oil into your drip pan
once it's empty you put the nut back on
just snug it up
you don't want to over do it
engine oil goes inside here were it says engine oil
this is your dipstick
throw your engine oil in here
I can't remember how much I put in there
doesn't take a whole lot
anyway on the dipstick it will tell you when its full
or when to add
and anywhere in between your okay
so once you think you got enough oil in there
start your engine up let it run for a few minutes
take this back out
and check your oil level
I got it right on the full mark
right up top so we're good
or I'm good
and that's pretty much it for oil change
not very difficult
alright new drive belt
now to get this on
it's pretty basic
take the tensioner and remove the tension, just pull it back
slide this off
get it off of here
get it off the bottom pulley
and without taking this piece off if I can
sneak it out of here
here we go
now you want to match it up
make sure it is the same belt
and now we'll just slide it through
okay I'm going to put it on
the bottom pulley
pull the tensioner back
out of the way
put it on the bottom pulley
past the tensioner
get it on the top pulley
not easy to get it on there
there we go
and release the tensioner
and it should be good
it's that easy
i'm going to go ahead and pull the engine
just to make sure it's on there good
okay, so drive belt, for the drive system is on
now to get this, front section
on
get the auger belt on
and now
we got to slide it back into place
there we go, probably going have to, loosen, these belt holders
get them out of the way
okay
now that you got the belt holders, thats what I call them
out of the way
pull the
adjuster back
and get that belt on there
just like that
then your going to put these back
where they were
get these top bolts started
snug them down
then we're going to flip this up
and tighten, those bottom bolts on the housing
alright, last thing i'm going to do
is I gotta put this back on here
there we go
washer on
cotter pin
now we just want to make sure this is adjusted properly
run it and check it
towards the belt to tighten it more, away from the belt to loosen it
what you want is about, when it's engaged
you want about a half inch deflection on there, more or less
on the belt movement back and forth about a half inch and your good
now as this belt wears out your gonna have to adjust this again
so you got quite a bit of adjustment left on here
so going to go ahead and lubricate the linkage
lubricate all this stuff with some WD-40
don't be afraid to spray this stuff on there
this one is not in bad shape but it is worn down so I'm just going to weld a new section to this
just a piece of metal that I got and that will make it last even longer
okay take these over to the bench
just going to weld some of this
onto there
and that will work pretty good man
look at that
there we go, nice
new skid plates
the snow blower on the ground
get these to touch the ground
and then we just tighten up
and what these do is it helps the cutting edge last longer
bears the weight in front of the snow blower
and it'll take this down while its taking down the cutting edge
if you didn't have these the cutting edge and the snow blower its self would just wear right out
let's get the cover back on
this cover back in
hook up the ground wire back
for the switch
and get these, back in place
put this back in
(music playing)
we'll that project is done
delivered
when he gets home he'll see it
he already knows he's getting that so
time to move on to other projects
and other things that need to be done around the house
charity work, just giving of your time and stuff
is ah is a great thing to do
you ought to try it
serve in a soup kitchen
read books to kids
their is so much you can do as far as charity work is concerned
and so many people out there that could really use a hand
so i'll leave you with that
y'all take care
god bless
y'all have a good day
bye bye