Hi DIY-ers, Sterling with Alarm Grid here.
Today, we're going to show you how
to pair your l5100 Wi-Fi communication
module to your Wi-Fi router.
This is a Lynx Touch l7000 panel,
and all of the Lynx Touch systems
after the l5000 have supported a Wi-Fi communicator.
One of the more popular questions we're asked
is how do we connect our device with our network?
So there's a couple ways to do it.
One is by entering the master code.
One, two, three, four is the default code,
and you can go to Wi-Fi config, and you have your option
to enroll it either by scanning for the access point
and using WPA encryption, meaning
typing in your Wi-Fi password.
There's also WPS encryption, which
you can use by pressing and holding
the WPS button on your router and then hitting the WPS
button on the panel.
I'm going to exit out of here, because I want to show you
another way to do it first.
That's the master code programming.
My personal favorite way to do it,
just because you get a little more activity and a little more
data, is to go into Regular Installer Mode programming.
So it was Security, More, Tools, type in your installer code.
By default, it's four, one, one two.
And then we can jump into Comm Diagnostics.
This is the same screen we used to find the MAC and the CRC
numbers for our devices.
But in this case, if we want to pair
to an actual Wi-Fi network, what we do
is we scan for access points.
This scan will highlight and show you any available networks
in the area.
Depending on where you are, how close your neighbors are,
or what Wi-Fi activity is in the area,
you may find multiple networks.
So you can see with the gold bars,
you have an indication of the signal strength
and you actually are also displayed with an actual dBm
level.
The lower the number, the better.
So typically, the best network is going to be at the top.
In this case, Donnelly is the home network
we're going to connect to.
We have this exclamation because we've previously
been joined to the network.
Normally, out of the box, you would not
have any indication of that.
So we're going to select it, and then edit.
Now you have your SSID name.
You need to have your SSID name broadcast for it
to pick it up here.
It auto-detects the security being used by the router, which
in this case, is WPA2.
And then we just hit key.
And we type in our password, done, and join.
So after a period of time, we get an indication
that the device has been successfully added
to the network.
If we keyed in the wrong password
or we had some sort of failure on the connection,
you would have seen an error message indicating as such.
In our case, we did it properly.
So if we hit OK, you can see the key is blank,
that's just for security purposes.
You might have noticed earlier this little Wi-Fi indicator was
showing an X. If we hit the back arrow, what
used to show as a red exclamation is now showing
has a green check mark, meaning we're active.
And if we back out a couple more times,
you can see now we are connected,
we have all four gold bars.
This used to be all grayed out.
And if we exit further, we are active on the network,
we are ready to activate monitoring or use
the Lynx Connect app to control the system.
And if we were to hit ethernet information,
you can see that it shows a physical link
54 Mbps, and that the DHCP is showing OK,
meaning we have a good solid connection to our network.
So now that we know we're good and connected,
we've shown you the way to connect
it using your Wi-Fi password.
A lot of times these Linksys routers out of the box,
or whichever router your cable company may be using
gives you a nice long complicated password.
Of course, you probably have that written down somewhere.
But a lot of people don't, and a lot of people
don't ever change the password for their router.
And therefore, if you don't want to deal
with typing in a long, complicated password,
there is another way that you can
pair your Wi-Fi communicator to your system, or to your router,
rather.
We're going to show you that.
First, what we're going to do just to break the connection,
is to edit, key, and we're going to just type
in the wrong password.
We're going to hit Done and Join.
We're just doing this just to show you basically,
we have to break the Wi-Fi connection to the router,
and then we're going to use the WPS encryption to show you
how you can roll it without having to use a key.
So after this joint is pressed, last time,
it said joined successfully because we
type in the right password.
On this case, we're going to get an error message that it
was not joined successfully.
There we go.
Failed operation, device not added to the network.
We hit OK, we're back to showing Wi-Fi with a red X. We're
back to showing the Wi-Fi has a red exclamation,
and if we exit all the way back to here,
we can see the network that it was last joined to is now
showing with no gold bars.
If we hit ethernet information, all of that good information
has gone to bad.
Physical link bad, DHCP bad.
That it is an indication that we are offline.
So now, we're going to show you WPS encryption.
Configue Wi-Fi.
Last time, we did scan access points.
We found our network, we edited our network,
and we typed in our password.
So this time, we're going to show you WPS encryption.
WPS is how you can use your router's WPS button and then
your device's WPS button, to have them sync
and join automatically.
Because you're pressing buttons on each,
they can communicate and establish
a good, solid connection securely,
without having to type in a password.
So because you're in the house you
have access to your router, your router normally,
the WPS button either has two chasing arrows indicating
a connection that way, or you'll have
a button that just clearly is displayed with the letters WPS.
Either way, your router may have it.
You simply press and hold the button,
which I'm going to have my partner do now.
When you press and hold the button,
typically, the router has some sort of indicator light
that you are now in the WPS mode.
You typically have so many minutes,
couple minutes after pressing the button to then press
the button on your WPS device.
In this case, our Lynx Touch l7000 is our WPS device.
So we've already done the WPS on the access point.
Now, we're going to select it on the panel.
And assuming everything works as expected,
we're going to get a nice solid Wi-Fi connection without having
to type in our Wi-Fi password.
Just like it did last time, it does take a minute or so.
And beautiful, device has been successfully added
to the network.
No Wi-Fi password needed.
If we hit OK and hit the back arrow,
we are joined back to the Donnelly network
with the four gold bars.
If we hit ethernet information, we're
back to showing the DHCP OK with a good physical link.
Our Wi-Fi indicator light is back to showing active,
and that is how you have two options
to join your l5100 Wi-Fi communicator
to your wireless router.
We hope this has been helpful and informative.
We invite you to subscribe to our channel.
And if you have any questions on your panel's Wi-Fi connection
or connecting to your router, please let us
know by emailing support@alarmgrid.com.